View CY7C1049CV33-12ZSXA_8323793.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

cy7c1049cv33 automotive 4-mbit (512 k 8) static ram cypress semiconductor corporation ? 198 champion court ? san jose , ca 95134-1709 ? 408-943-2600 document number: 001-67511 rev. *c revised march 21, 2014 4-mbit (512 k 8) static ram features temperature ranges ? automotive -a: ?40 c to 85 c ? automotive-e: ?40 c to 125 c high speed ? t aa = 10 ns low active power ? 360 mw (max) 2.0 v data retention automatic power down when deselected ttl-compatible inputs and outputs easy memory expansion with ce and oe features functional description the cy7c1049cv33 automotive is a high performance cmos static ram organized as 524,288 words by eight bits. easy memory expansion is provided by an active low chip enable (ce ), an active low output enable (oe ), and three-state drivers. writing to the device is accomplished by taking chip enable (ce ) and write enable (we ) inputs low. data on the eight i/o pins (i/o 0 through i/o 7 ) is then written into the location specified on the address pins (a 0 through a 18 ). reading from the device is accomplished by taking chip enable (ce ) and output enable (oe ) low while forcing write enable (we ) high. under these conditions, the contents of the memory location specified by the address pins appear on the i/o pins. the eight input and output pins (i/o 0 through i/o 7 ) are placed in a high impedance state when the device is deselected (ce high), the outputs are disabled (oe high), or during a write operation (ce low, and we low). the cy7c1049cv33 automotive is available in standard 400-mil-wide 36-pin soj package and 44-pin tsop ii package with center power and ground (revolutionary) pinout. a 0 io 0 io 7 io 1 io 2 io 3 io 4 io 5 io 6 a 1 a 2 a 3 a 4 a 5 a 6 a 7 a 8 a 9 sense amps power down ce we oe a 13 a 14 a 15 a 16 a 17 row decoder column decoder 512k x 8 array input buffer a 10 a 11 a 12 a 18 logic block diagram
cy7c1049cv33 automotive document number: 001-67511 rev. *c page 2 of 15 contents selection guide ................................................................ 3 pin configuration ............................................................. 3 pin definitions .................................................................. 3 maximum ratings ............................................................. 4 operating range ............................................................... 4 electrical characteristics ................................................. 4 capacitance ...................................................................... 5 thermal resistance .......................................................... 5 ac test loads and waveforms ....................................... 5 ac switching characteristics ......................................... 6 switching waveforms ...................................................... 7 truth table ........................................................................ 9 ordering information ...................................................... 10 ordering code definitions ......................................... 10 package diagrams .......................................................... 11 acronyms ........................................................................ 13 document conventions ................................................. 13 units of measure ....................................................... 13 document history page ................................................. 14 sales, solutions, and legal information ...................... 15 worldwide sales and design s upport ......... .............. 15 products .................................................................... 15 psoc? solutions ...................................................... 15 cypress developer community ................................. 15 technical support ................. .................................... 15
cy7c1049cv33 automotive document number: 001-67511 rev. *c page 3 of 15 selection guide description -10 -12 -15 unit maximum access time 10 12 15 ns maximum operating curre nt automotive-a 100 95 ? ma automotive-e ? ? 95 ma maximum cmos standby current automotive-a 10 10 ? ma automotive-e ? ? 15 ma pin configuration figure 1. 36-pin soj pinout (top view) figure 2. 44-pin tsop ii pinout (top view) 1 2 3 4 5 6 7 8 9 10 11 14 23 24 28 27 26 25 29 32 31 30 12 13 33 36 35 34 16 15 21 22 gnd a 1 a 2 a 3 a 4 a 5 a 6 a 7 a 8 we v cc a 18 a 15 a 12 a 14 i/o 5 i/o 4 a 9 a 0 i/o 0 i/o 1 i/o 2 oe a 17 a 16 a 13 ce 18 17 19 20 gnd i/o 7 i/o 3 i/o 6 v cc a 10 a 11 nc nc a 6 1 2 3 4 5 6 7 8 9 10 11 14 31 32 36 35 34 33 37 40 39 38 12 13 41 44 43 42 16 15 29 30 v cc a 7 a 8 a 9 nc nc nc nc a 18 v ss nc a 15 a 0 a 3 i/o 0 a 4 ce a 17 a 12 a 1 a 2 18 17 20 19 i/o 1 27 28 25 26 22 21 23 24 nc v ss we i/o 2 i/o 3 a 5 nc a 16 v cc oe i/o 7 i/o 6 i/o 5 i/o 4 a 14 a 13 a 11 a 10 nc nc nc pin definitions pin name 36-pin soj pin number 44-pin tsop ii pin number i/o type description a 0 ?a 18 1?5, 14?18, 20?24, 32?35 3?7, 16?20, 26?30, 38?41 input address inputs used to select one of the address locations . i/o 0 ?i/o 7 7, 8, 11, 12, 25, 26, 29, 30 9, 10, 13, 14, 31, 32, 35, 36 input/output bidirectional data i/o lines . used as input or output lines depending on operation. nc [1] 19, 36 1, 2, 21, 22, 23, 24, 25, 42, 43, 44 no connect no connects . this pin is not connected to the die. we 13 15 input/control write enable input, active low . when selected low, a write is conducted. ce 6 8 input/control chip enable input, active low . when low, selects the chip. when high, deselects the chip. oe 31 37 input/control output enable, active low . controls the direction of the i/o pins. when low, the i/o pins are allowed to behave as outputs. when deasserted high, i/o pins are tri-state, and act as input data pins. v ss , gnd 10, 28 12, 34 ground ground for the device . should be connected to ground of the system. v cc 9, 27 11, 33 power supply power supply inputs to the device . note 1. nc pins are not connected on the die.
cy7c1049cv33 automotive document number: 001-67511 rev. *c page 4 of 15 maximum ratings exceeding maximum ratings may impair the useful life of the device. these user guidelines are not tested. storage temperature ............................... ?65 ? c to +150 ?? c ambient temperature with power applied ... .............. .............. .......... ?55 ? c to +125 ? c supply voltage on v cc to relative gnd [2] ......................... ?0.5 v to +4.6 vdc voltage applied to outputs in high z state [2] ................................ ?0.5 v to v cc + 0.5 v input voltage [2] .................................. ?0.5 v to v cc + 0.5 v current into outputs (low) .... .................................... 20 ma static discharge voltage (mil-std-883, method 3015) ................................. > 2001 v latch up current ..................................................... > 200 ma operating range range ambient temperature v cc automotive-a ?40 ? c to +85 ? c 3.3 v ? 0.3 v automotive-e ?40 ? c to +125 ? c electrical characteristics over the operating range parameter description test conditions -10 -12 -15 unit min max min max min max v oh output high voltage v cc = min; i oh = ?4.0 ma 2.4 ? 2.4 ? 2.4 ? v v ol output low voltage v cc = min; i ol = 8.0 ma ?0.4?0.4?0.4 v v ih input high voltage 2.0 v cc + 0.3 2.0 v cc + 0.3 2.0 v cc + 0.3 v v il input low voltage [2] ?0.3 0.8 ?0.3 0.8 ?0.3 0.8 v i ix input load current gnd < v i < v cc auto-a ?1 +1 ?1 +1 ? ? ? a auto-e?????20+20 i cc v cc operating supply current v cc = max, f = f max = 1/t rc auto-a ? 100 ? 95 ? ? ma auto-e?????95 i sb1 automatic ce power down current ? ttl inputs max. v cc , ce > v ih ; v in > v ih or v in < v il , f = f max auto-a ? 40 ? 40 ? ? ma auto-e?????45ma i sb2 automatic ce power down current ? cmos inputs max. v cc , ce > v cc ? 0.3 v, v in > v cc ? 0.3 v, or v in < 0.3 v, f = 0 auto-a ? 10 ? 10 ? ? ma auto-e?????15ma note 2. v il(min) = ?2.0 v and v ih(max) = v cc + 0.5 v for pulse durations of less than 20 ns.
cy7c1049cv33 automotive document number: 001-67511 rev. *c page 5 of 15 capacitance parameter [3] description test conditions max unit c in input capacitance t a = 25 ? c, f = 1 mhz, v cc = 3.3 v 8 pf c out output capacitance 8pf thermal resistance parameter [3] description test conditions 36-pin soj 44-pin tsop ii unit ? ja thermal resistance (junction to ambient) test conditions follow standard test methods and procedures for measuring thermal impedance, per eia / jesd51. 46.51 41.66 c/w ? jc thermal resistance (junction to case) 18.8 10.56 c/w ac test loads and waveforms figure 3. ac test loads and waveforms [4] 90% 10% 3.0 v gnd 90% 10% all input pulses 3.3 v output 30 pf * capacitive load consists of all components of the test environment (b) r 317 ? r2 351 ? rise time: 1 v/ns fall time: 1 v/ns 30 pf* output z = 50 ? 50 ? 1.5 v (c) (a) 3.3 v output 5 pf (d) r 317 ? r2 351 ? 10-ns devices: 12-, 15-ns devices: high z characteristics: notes 3. tested initially and after any design or process changes that may affect these parameters. 4. ac characteristics (except high z) for 10 ns parts are tested using the load conditions shown in figure 3 (a). all other speeds are tested using the thevenin load shown in figure 3 (b). high z characteristics are tested fo r all speeds using the test load shown in figure 3 (d).
cy7c1049cv33 automotive document number: 001-67511 rev. *c page 6 of 15 ac switching characteristics over the operating range parameter [5] description -10 -12 -15 unit min max min max min max read cycle t power [6] v cc (typical) to the first access 100 ? 100 ? 100 ? ? s t rc read cycle time 10?12?15? ns t aa address to data valid ? 10 ? 12 ? 15 ns t oha data hold from address change 3?3??3 ns t ace ce low to data valid ?10?12?15 ns t doe oe low to data valid ?5?6?7 ns t lzoe oe low to low z [7] 0?0?0? ns t hzoe oe high to high z [7, 8] ?5?6?7 ns t lzce ce low to low z [7] 3?3?3? ns t hzce ce high to high z [7, 8] ?5?6?7 ns t pu ce low to power up 0?0?0? ns t pd ce high to power down ? 10 ? 12 ? 15 ns write cycle [9, 10] t wc write cycle time 10?12?15? ns t sce ce low to write end 7 ? 8 ? 10 ? ns t aw address setup to write end 7 ? 8 ? 10 ? ns t ha address hold from write end 0?0?0? ns t sa address setup to write start 0?0?0? ns t pwe we pulse width 7 ? 8 ?10? ns t sd data setup to write end 5?6?7? ns t hd data hold from write end 0?0?0? ns t lzwe we high to low z [7] 3?3?3? ns t hzwe we low to high z [7, 8] ?5?6?7 ns notes 5. test conditions assume signal transition ti me of 3 ns or less, timing reference levels of 1.5 v, input pulse levels of 0 to 3 .0 v. 6. t power gives the minimum amount of time that the power supply should be at stable, typical v cc values until the first memory access can be performed. 7. at any temperature and voltage condition, t hzce is less than t lzce , t hzoe is less than t lzoe , and t hzwe is less than t lzwe for any device. 8. t hzoe , t hzce , and t hzwe are specified with a load capacitance of 5 pf as in part (d) of figure 3 on page 5 . transition is measured 500 mv from steady-state voltage. 9. the internal write time of the memory is defined by the overlap of ce low, and we low. ce and we must be low to initiate a write, and the transition of either of these signals can terminate the write. the input data setup and hol d timing should be referenced to the leading edge of the sig nal that terminates the write. 10. the minimum write cycle time for write cycle no. 2 (we controlled, oe low) is the sum of t hzwe and t sd .
cy7c1049cv33 automotive document number: 001-67511 rev. *c page 7 of 15 switching waveforms figure 4. read cycle no. 1 (address transition controlled) [11, 12] figure 5. read cycle no. 2 (oe controlled) [12, 13] figure 6. write cycle no. 1 (we controlled, oe high during write) [14, 15] previous data valid data valid rc t aa t oha t rc address data out 50% 50% data valid t rc t ace t doe t lzoe t lzce t pu high impedance t hzoe t hzce t pd impedance i cc i sb high address ce data out v cc supply current oe data valid t hd t sd t pwe t sa t ha t aw t sce t wc t hzoe address ce we data i/o oe note 16 notes 11. device is continuously selected. oe , ce = v il . 12. we is high for read cycles. 13. address valid before or similar to ce transition low. 14. data i/o is high impedance if oe = v ih . 15. if ce goes high simultaneously with we high, the output remains in high impedance state. 16. during this period, the i/os are in output state. do not apply input signals.
cy7c1049cv33 automotive document number: 001-67511 rev. *c page 8 of 15 figure 7. write cycle no. 2 (we controlled, oe low) [17, 18] switching waveforms (continued) data valid t hd t sd t lzwe t pwe t sa t ha t aw t sce t wc t hzwe address ce we data i/o note 19 notes 17. if ce goes high simultaneously with we high, the output remains in high impedance state. 18. the minimum write cycle time for write cycle no. 2 (we controlled, oe low) is the sum of t hzwe and t sd . 19. during this period, the i/os are in output state. do not apply input signals.
cy7c1049cv33 automotive document number: 001-67511 rev. *c page 9 of 15 truth table ce oe we i/o 0 ?i/o 7 mode power h x x high z power down standby (i sb ) l l h data out read active (i cc ) l x l data in write active (i cc ) l h h high z selected, outputs disabled active (i cc )
cy7c1049cv33 automotive document number: 001-67511 rev. *c page 10 of 15 ordering code definitions ordering information speed (ns) ordering code package diagram package type operating range 10 cy7c1049cv33-10vxa 51-85090 36-pin (400-m il) molded soj (pb-free) automotive-a 12 CY7C1049CV33-12ZSXA 51-85087 44-pin tsop ii (pb-free) automotive-a 15 cy7c1049cv33-15vxe 51-85090 36-pin (400-m il) molded soj (pb-free) automotive-e cy7c1049cv33-15zsxe 51-85087 44-pin tsop ii (pb-free) automotive-e temperature range: x = a or e a = automotive-a or e = automotive-e x = pb-free; x absent = leaded package type: xx = v or zs v = 36-pin (400-mil) molded soj zs = 44-pin tsop ii speed grade: xx = 10 ns or 12 ns or 15 ns v33 = 3.0 v to 3.6 v process technology: c ? 150 nm data width: 9 = 8-bits density: 04 = 4-mbit density family code: 1 = fast asynchronous sram technology code: c = cmos marketing code: 7 = sram company id: cy = cypress cy 1 c - xx xx x v33 x c 04 9 7
cy7c1049cv33 automotive document number: 001-67511 rev. *c page 11 of 15 package diagrams figure 8. 36-pin soj v36.4 (molded) package outline, 51-85090 51-85090 *f
cy7c1049cv33 automotive document number: 001-67511 rev. *c page 12 of 15 figure 9. 44-pin tsop z44-ii package outline, 51-85087 package diagrams (continued) 51-85087 *e
cy7c1049cv33 automotive document number: 001-67511 rev. *c page 13 of 15 acronyms document conventions units of measure acronym description ce chip enable cmos complementary metal oxide semiconductor i/o input/output oe output enable soj small outline j-lead sram static random access memory tsop thin small outline package ttl transistor-transistor logic we write enable symbol unit of measure c degree celsius mhz megahertz a microampere s microsecond ma milliampere mm millimeter ms millisecond mw milliwatt ns nanosecond ? ohm % percent pf picofarad vvolt wwatt
cy7c1049cv33 automotive document number: 001-67511 rev. *c page 14 of 15 document history page document title: cy7c1049cv33 automotive, 4-mbit (512 k 8) static ram document number: 001-67511 rev. ecn orig. of change submission date description of change ** 3186792 pras 03/03/2011 separation of the automo tive data sheet from cy7c1049cv33 spec no. 38-05006 rev. *j. further rev of 38-05006 would include only industrial / commercial parts. *a 3265070 pras 05/24/2011 updated functional description (removed ?for best practice recommendations, refer to the cypress application note an1064, sram system guidelines.?). updated in new template. *b 3546915 nile 03/09/2012 updated pin definitions (updated description of we and oe pins). updated package diagrams . *c 4311615 nile / vini 03/21/2014 updated maximum ratings : added ?static discharge voltage? and ?latch up current? details. updated ac switching characteristics : updated note 10. updated switching waveforms : added note 18 and referred the same note in figure 7 . updated package diagrams : spec 51-85087 ? changed revision from *d to *e. updated in new template. completing sunset review.
document number: 001-67511 rev. *c revised march 21, 2014 page 15 of 15 all products and company names mentioned in this document may be the trademarks of their respective holders. cy7c1049cv33 automotive ? cypress semiconductor corporation, 2011-2014. the information contained herein is subject to change without notice. cypress s emiconductor corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a cypress product. nor does it convey or imply any license under patent or other rights. cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement wi th cypress. furthermore, cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. the inclusion of cypress products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies cypress against all charges. any source code (software and/or firmware) is owned by cypress semiconductor corporation (cypress) and is protected by and subj ect to worldwide patent protection (united states and foreign), united states copyright laws and internatio nal treaty provisions. cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of, and compile the cypress source code and derivative works for the sole purpose of creating custom software and or firmware in su pport of licensee product to be used only in conjunction with a cypress integrated circuit as specified in the applicable agreement. any reproduction, modification, translation, compilation, or repre sentation of this source code except as specified above is prohibited without the express written permission of cypress. disclaimer: cypress makes no warranty of any kind, express or implied, with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. cypress reserves the right to make changes without further notice to t he materials described herein. cypress does not assume any liability arising out of the application or use of any product or circuit described herein. cypress does not authori ze its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. the inclusion of cypress? prod uct in a life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies cypress against all charges. use may be limited by and subject to the applicable cypress software license agreement. sales, solutions, and legal information worldwide sales and design support cypress maintains a worldwide network of offices, solution center s, manufacturer?s representatives, and distributors. to find t he office closest to you, visit us at cypress locations . products automotive cypress.co m/go/automotive clocks & buffers cypress.com/go/clocks interface cypress. com/go/interface lighting & power control cypress.com/go/powerpsoc cypress.com/go/plc memory cypress.com/go/memory psoc cypress.com/go/psoc touch sensing cyp ress.com/go/touch usb controllers cypress.com/go/usb wireless/rf cypress.com/go/wireless psoc ? solutions psoc.cypress.com/solutions psoc 1 | psoc 3 | psoc 4 | psoc 5lp cypress developer community community | forums | blogs | video | training technical support cypress.com/go/support

▲Up To Search▲

Price & Availability of CY7C1049CV33-12ZSXA

	To Download CY7C1049CV33-12ZSXA Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .